| Customization: | Available |
|---|---|
| Cooling Way: | Water Cooling |
| Control: | Semi-Automatic |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
SAILTON Brand MFDC Transformer controller Spot welder controller ,1000-2000Hz Mfdc Resistance Welder controller ZMF-T400/ZMF400A
| Technical parameters | ||
| Electrical characteristics | Power input | AC380V±10% |
| Power frequency | 50Hz±10% | |
| Inverter frequency |
1KHz | |
| Output voltage |
PWM500V |
|
| Output current |
400A-3600A |
|
| Rated duty cycle |
10% |
|
| Constant current output accuracy |
Current change ≤ 2% (when impedance changes ±15%) |
|
| Current repeatability |
2% |
|
| Valve specifications |
DC24V |
|
| Single-way gas valve power |
≤5W |
|
| Total output power of gas valve |
≤30W | |
| Working environment requirement | Ambient temperature |
5-45°C |
| Ambient humidity |
≤85% |
|
| Environmental requirements |
No corrosive gas and conductive dust |
|
| Cooling water flow |
≥6L/min-20L/min |
|
| Cooling water temperature |
≤40ºC |
|
| Cooling water temperature difference |
≤15°C (no condensation) |
|
| Cooling water requirements |
Non-corrosive | |
| Radiator temperature upper limit |
65°ºC |
|
Brief introduction
Medium-frequency (MF) transformers are a result of recent advances in resistance welding technology.
They arepowered by a transistor inverter, supplying square wave AC 500 V @ 1000 Hz which is converted by the MF transformer to a low voltage high current AC.
This low voltage AC current is rectified to DC by a diode block built into the transformer.
The higher operating frequency of an MF system allows efficient energy conversion using a smaller and lighter transformer.
Other benefits with MF transformers used in portable and robotic welding guns are:
The reactance of the welding loop only limits the upslope and down slope of the welding current.
While the peak welding current in limited only by the welding loop's resistance.
The net result is again smaller transformer, especially when welding with large throat, high-impedance guns.
MF welding is less demanding on the plant power system.
The MF inverter draws balanced line current from all 3 phases and operates at a high power factor (0.9).
With MF transformers the peak welding current almost equals its RMS value, which helps to obtain quality welds with no splash and constantstrength even at lower pressure.
The high frequency permits much faster - 1000 times per second - process control, which again results in better weld quality.
Application
For all kinds of intermediate frequency, power frequency
resistance welding machine.Such as automobile welding clamp,
seam welding machine, mesh welding machine and so on.
| Technical parameter | ||||||||||
| TYPE | MF130GD | |||||||||
| Primary nominal voltage | V | 500 | ||||||||
| Frequency | Hz | 1000 | ||||||||
| Nominal power at 20%ED | kVA | 130 | ||||||||
| Nominal power at 50%ED | kVA | 85 | ||||||||
| Nominal power at 100%ED | kVA | 58 | ||||||||
| Secondary voltage | V | 9 | ||||||||
| Permanent DC current 100% | A | 6500 | ||||||||
| Short circuit current | KA | 32 | ||||||||
| Turns ratio | N1 / N2 | 55:1 | ||||||||
| Weight | kg | 15 | ||||||||
| Temperatur switch | 2 x 150 °C, 1 x 70 °C Temperature switch | |||||||||
| Insulation class | F (155 °C) | |||||||||
| Current measuring coil | -- | |||||||||
| Size | mm | 150X106X358 | ||||||||
| Cooling water < 30°C | L/ min | 8 | ||||||||
| Pressure drop | Mpa | <0.2 | ||||||||
Company Certificate
){kind=link}